Coleman Hot Tub Error Codes
Answers to common Lay-Z-Spa issues as well as advice and troubleshooting from the official home of Lay-Z-Spa. Coleman Lay-Z Spa. Sign Up for Offers. Enter Your Email Submit. Follow Coleman. We are a wholesale distributor of spa and hot tub parts. We sell exclusively to pool & spa professionals.
• dry: Inadequate flow in heater. (Displays on third occurrence of 'dr' message) • Pr: When spa is first actuated, it will go into Priming Mode • ---: Unknown water temp. • Std: Spa operating in Standard Mode. • Ecn: Spa operating in Economy Mode. • SE: Spa operating in Standard-in-Economy Mode. • ILOC: Interlock failure - possible pump/ozone spike Brett Aqualine Error Codes • OH: Temp exceeds 118 F • Fr: Freeze condition - temp below 40 degrees • FL: Pressure switch failure • EO: Shorted temp sensor • E1: Open temp sensor • E2: Shorted hi-limit sensor • E3: Open hi-limit sensor • E4: Shorted flow switch • E7: Improper electrical connection CTI Error Codes • thl/39: temp probe problem • th2/current temp: temp probe problem • th3/39: water temp below 39° F • OH: water over 112° F. System will restart when temp.
A Pump appears to have been stuck ON before a GFCI trip, causing an extreme overheat. If the extreme overheat conditions are determined, a spa with the GFCI Trip Feature enabled will trip the GFCI and shut down the power to the spa. If the GFCI does not trip for some reason, the gFI fault will appear and the HOt flag will be set. If the spa is subsequently powered down and then powered up again, the HOt message will appear on the display and the spa will not be allowed to operate until a technician evaluates the spa and resets the HOt fault. Note: The HOt message indicates the spa WAS in an extremely serious condition before power was shut off to the spa. It may be possible for a stuck relay to free itself after the power cycle, but the spa cannot clear the the HOt message without starting up in Test Mode first.
Driverdoc keygen. Unlike the Coleman Slauspa, Intex model comes with an entire set of accessories that are necessary for any tub. This includes extra filter cartridges, chemical testing strips, and a chlorine dispenser.
A floating lighting device that will brighten up your spa and add some mood lighting in the evening. Check it out here • Hot tub chemicals: Keeping your water appropriately tested and using the correct chemicals is very important. Check a complete guide about. • Mosaic print pool liner with cushioned floor and convenient drain valve • Insulated Cover: When you aren’t using the tub, the cover that is insulated with an aluminum foil coating maintains heat and keeps out debris.
• If the E11 error code is visible again, place a further 0.5kg (500g) of Pure Spa Salt in the spa. E12 ← swipe →. Description Cause Solution Water Leakage. Error code for an issue with water leaking within the body of the pump. • Check the couplings on the pump connections to ensure there is no water leaking from these. • Also ensure the washers within these are flat. • These can be checked using a screwdriver and simply unscrewing the coupling.
The Spa is Operating in 'Priming' (Pr) Mode. The Spa has just been powered up and is in Priming Mode for 4 Minutes. Pumps and Blower can be turned ON and OFF to Remove any Air from the Heater. On EL and GL Systems Only, equipped with a 'Mode' Button, the Ozone Generator can be Turned ON for 15 Seconds and OFF by using the 'Mode' Button.
There are 2 handles built into the sides for easy transportation. This package also includes a chemical floater to keep your spa clean, a twin pack of filter cartridges, and an inflatable cover to keep your water warm when you’re not using it. Enjoy the luxury of a hot tub in your house by yourself, with friends, or as a romantic treat with the Coleman Inflatable Miami Spa. Thinking to buy it?
- If the display exits Priming Mode and shows dashes or a temperature or a mode indication (such as Std or Ecn or SLP) before you have finished verifying that all your pumps are primed, turn off the power at the main power panel IMMEDIATELY, then turn it back on, to initiate a new pump priming mode. Important: A pump should not be allowed to run without priming for more than 2 minutes. Under NO circumstances should a pump be allowed to run without priming beyond the end of the 4 minute Priming Mode. Doing so may cause damage to the pump and cause the system to go into an overheat condition.
Coleman Hot Tub Error Code E02
• Turn the pump unit off and unplug from the socket (leave for 10 seconds). • Plug the pump unit back in and turn it back on. • Press the thermal reset button for 10 seconds using a pencil or screwdriver (see for location) • Once done, press the heater button. Your pump should now be working. E05 ← swipe →. Description Cause Solution Temperature too high The thermostat is broken. If the troubleshooting has been completed without success, for more help with this Pump needs to be reset.
Ive owned my coleman spa for 4 months now. I was getting the error code 1- 3 times a week, consistant with how many times I was in it per week.
Other issues that can cause these error codes is debris wrapped around the pump impeller, or one of the valves is not open up all the way. The most common valve; the tee handle valve, will show that the handle is up, but in many cases the gate is still half closed, make sure that it is open all the way, you may need to dismantle the fittings to look inside. At the same time this test is being done, put your hand on the stainless steel heater manifold, it should NOT be hot, it should only be at the same temperature the water in the spa is. If it is hot you have a flow issue, or if it stays hot after the pump is shut off either the pressure switch has stuck close (see FLO error codes above) or the relays on the board have stuck shut sending continuous power to the heater.
Coleman Hot Tub Error Code 01 21
Spas with Pump Suction Blockage Switch: 1. The 'SF' Safety Fault Error Message indicates that the Vacuum Switch has closed, indicating that there has been a Suction Problem or a Possible Entrapment Situation Avoided. Press Any Button to Reset and Clear the Error Message.
Spa is shut down. Pr = When spa is first actuated, it will go into Priming Mode. ILOC = Interlock failure - possible pump or ozone spike. (---) =Unknown water temperature. (Displays when first powered up after refill).
Contact qualified service technician. For more information regarding CTI tech support th1/39 On startup indicates temperature probe problem. Th2/current temperature On startup indicates temperature probe problem. Th3/39 On startup indicates water temperature less than 39° F. Overheating, water over 112° F.
Pressed on and hey presto away it went. Hope yours is as easy to fix •.